Showing posts with label Fabric. Show all posts
Showing posts with label Fabric. Show all posts

11.14.2010

Holiday Table Runners

We sewed table runners for Thanksgiving!

Table Runners
For mine (left), I used one strip of about 1 1/4 yeards of heavy fabric cut 16 inches wide (2 of those inches were for seam allowances). I simply folded down where I was going to hem the edges with an iron and then sewed away.
For Jen's, she used two different fabrics to make a revisible Thanksgiving/Winter table runner. She simply sewed the fabric right-sides together along three edges, turned the fabric right-side out, and hand-sewed the fourth edge.
For Stacy's (bottom), she used two different fabrics too, but to make her runner extra long, she joined her fabric at the middle of her runner and sewed it together on the bias to make the seam less obvious.

Simple Valance (to go with the Table Runner)
I basically hemmed a rectangle then folded one long side over and sewed it to make a pocket for the rod to go through.

Note: For heavy fabric, you may have to adjust/increase the tension on your sewing machine.









Helpful link: Table Runner Tutorial

9.26.2010

Sewing Night: Fleece Socks/Slippers




Socks/Slippers Project: Buy an easy fleece sock/slipper pattern. Alternatively, cut out for each slipper:
  • A) Sole - Piece for around the bottom of your foot
  • B) Heel - Piece going frombottom of your heel to 4 inches above your ankle
  • C) Top - Piece for over the top of your foot going from the tip of your toes to 4 inches above your ankle
Be sure to cut out the pieces so the direction of most stretch runs across them, not top-to-bottom. Now sew the sole piece to the heel piece, right-sides together, along the base of the heel. Next, turn the seam allowances in towards the heel piece and sew, this time using a zigzag stitch. Now, unfold the sole-heel combination and pin to the top piece with wrong-sides facing out. Sew all the way around the outside of the slipper leaving an opening at the top for your foot to enter. Turn the slipper right-side out. The only thing left is sewing the cuff - Fold about one inch of the cuff inside the slipper and sew all the way around the cuff once. Done!
For those who do not know how to load a sewing machine: Here are some general instructions – you will still need your sewing machine’s manual. Turn your machine on. Load thread onto a bobbin using the bobbin-winder on the top of your machine. Now, load the bobbin into the chamber underneath your machine. Next, load your spool of thread on top of your machine and follow your manual’s directions to get it to come out near the sewing needle. For my machine, the thread has to be caught by a little hook at the top of the machine, and then feed down and around a knob, then up and through a hook, then down and through another hook. Next thread your sewing needle from front to back and hook the thread throug the foot. To get the thread from the bobbin underneath up, turn the knob on the side of your machine until the needle comes down and hooks and loops that thread. Keep turning the knob and it will bring up the thread. Pull both of the threads (the one coming from the top and the one coming from underneath) up and away from you and your machine so they won’t slip away. Place the foot down to clamp your fabric under the needle. Begin sewing!

7.15.2010

Batik Dying: Skirt and Purse

Skirt project: We used red, purple, and black dye in that order and a paint brush. Before dying the fabric, a design was painted on with wax. After the skirt was dyed red, the excess dye was rinsed out but the wax was left on. Next, more designs were painting on with wax and the skirt was dyed purple. Then too the skirt was rinsed and allowed to dry without removing the wax. Finally, more designs were painted on with wax, and the skirt was dyed black. The skirt was rinsed with water to remove the excess dye, and then run in the washing machine on the hot cycle to remove the wax.

Note: The red dye came out more pink than red, and the black dye came out more purple than black.

Purse project: We used a star stencil, a paintbrush, and blue and yellow dye. Using the stencil as a guide, I painted wax along the inner edge of the stencil. When finished with the design, I added blue dye and yellow dye in a ratio of approx. 2 parts blue to 1 part yellow. Using two colors created a more muted color when the project was finished – I think the more different colors you mix in one dying bath, the more muted the final color of the dyed fabric will be.

Note: Before the wax was hot enough, the painting was more difficult and the wax didn't get into the fabric as well. Try to get your wax really hot so it glides across the fabric.
For those who do not know how to Batik: Get beeswax and heat until it until it's very runny. Meanwhile, you can draw your design on your fabric with a pencil (the marks will wash out). Use paintbrushes to dip into the wax and “paint” with it on your fabric. The areas you paint with wax will not absorb color when dyed. You can also use metal cookie-cutters as stencils. When you are finished painting your design, it’s time to dye the fabric. Get a large bucket. We used an old kitty litter bucket. Fill 3/4 full with water and add dye according to package directions. We used Rid dye – it’s available at Walmart and Michael’s. Immerse fabric and stir several times over the course of 20 minutes. The longer the fabric is in the dye, the richer and darker the color will be. Also, you can combine more than one packet of dye in order to get a mixed and/or more subtle color. Next, toss out the dyed water and rinse your fabric in water in the sink or bathtub to remove the excess dye. Finally, boil water and remove it from the heat source, then put your fabric into the boiled water to remove the wax. You can add a bit of detergent to the boiled water to make removing the wax easier. For us, we chose instead to remove the wax by running the fabric through the washing machine on the hot cycle. However, the wax may clog your washing machine, so weigh that risk when deciding what you do.

Notes: For us batik-dying was a multi-night project. Also, the fabric ended up lighter than when it was first pulled out of the dye bath. Be aware of that when choosing how long to leave your fabric in the dye bath.